![]() ![]() Guidance on the International Symbol of AccessibilityĬhapter 10: Recreational Boating FacilitiesĬhapter 10: Swimming Pools, Wading Pools, and Spas A smaller bit will also help prevent any splintering on the backside of the cabinet as you drill through-for extra protection, place a strip of masking tape over your marked spot before drilling in.Chapter 3: Clear Floor or Ground Space and Turning SpaceĬhapter 6: Washing Machines and Clothes Dryers Once you drill into the cabinet, there's no turning back. When you start drilling, begin with the smallest drill bit possible. Then use a level to ensure all the holes and hardware will be level for the upper cabinets and then the lower cabinets. Line crosshair up with the hole in the jig, then mark the hole where you will pre-drill.Īfter you've triple-checked your mark for the drill hole, repeat the process for all of your cabinetry. Use the tape measure to find the center of the cabinet door, then mark it with a pencil this will create a crosshair with the horizontal line of the cabinet. If not, you can re-drill or fill any existing holes to suit new hardware with the same center-to-center, or get a wider center-to-center size that covers up any existing holes.įor drilling your own holes, start with a tape measure and a jig template. The easiest choice is to replace your existing hardware with an option that has the same mount type (surface or back-facing) and center-to-center measurement. If you have pre-drilled holes or existing hardware, you have a few options. Do this by dividing the drawer into thirds and place your hardware on the left and right portions. Although rules are always made to be broken, for example, using pulls all over can give your space a sleek, contemporary feel.Īlso, if your drawers are longer than 24 inches, double up on knobs or pulls. For drawers, center the hardware in the middle of the drawer, both horizontally and vertically.Īs a general rule of thumb for traditional spaces, place knobs on doors and pulls on drawers. On lower cabinets, hardware should be on the upper corner opposite the hinge. Cabinet knobs and cabinet pulls are usually placed between 2 1/2 and 3 inches from the corner of the cabinet door (the side opposite from the hinges).įor upper cabinets, hardware should be placed on the lower corner. While the exact placement of knobs and pulls is open to personal preference, there are standard measurements that will suit most kitchens. Knobs on doors, pulls on drawers: Install handle pulls on all drawers for easier use, especially if any of them will hold heavy items.Knobs on uppers, pulls on lowers: Mix and match knobs and pulls based on your style of cabinetry simple knobs are ideal for clear glass doors.All pulls: For a more sleek look, handle pulls are easy to grab and can be installed vertically or horizontally.All knobs: Knobs offer an easy-to-install option that doesn’t take up much space on your cabinetry.Slot-Head Screws: Traditional, solid brass screws used to mount hardware on the face of your cabinet.īolt-Mount Screws: Used to mount hardware from the backside of your cabinet.Īs shown above, here are four different ways to use cabinet pulls and knobs on your drawers and doors: Jig: A cabinet hardware jig ( shop our easy-to-use option here) is a plastic template that has pre-measured holes, offering easy correct placement for your cabinet hardware. For cabinet pulls, standard center-to-center screw holes measure between 3 to 5 inches, or 64, 96, and 128 millimeters apart. Drill + small drill bit (if drilling custom holes)Ĭenter-to-center: This measures the space between the two screw holes used to install each side of a drawer pull, which could be slightly wider or narrower than the total length of your drawer pull.See our list of essentials and key measurements below so you have all the information you need before starting. If you're drilling the holes yourself, there's a bit more information involved to ensure you get it right the first time. If you're ordering new cabinetry for your kitchen or bath, you'll want check the measurements for any pre-drilled holes so they align with your hardware size. Before purchasing, make sure you check the mounting type and center-to-center size of your existing hardware or pre-drilled holes. Our cabinet hardware comes equipped with all the necessary screws and mounting hardware, making installation easy. ![]() Switching your cabinet hardware takes only minutes for each cabinet-all you need is a measuring tape, standard screwdriver, and your new hardware. Swap out your existing kitchen hardware for a quick refresh, or complete your new bathroom vanity with a set of drawer pulls. Installing new hardware provides the perfect finishing touch for your space, whether you're planning a full kitchen remodel or doing a DIY cabinet update. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |